• Mold clamping force calculation using SW thermal simulation.

    Hello, Please let me know the possibility to calculate below requirement using SW simulation premium. This is a draft of a mold. I needed to calculate the clamping force F when the rubber strip temperature reached ...
    Heshantha Manupriya
    last modified by Heshantha Manupriya
  • Custom Material Modulus Error

    Hi all, I study dynamic materials and I am hoping to run a reasonably simple tensile test simulation with a 12.5 x 9 mm custom material. I would use a Nonlinear dynamic study and I would upload my stress-strain curve...
    Marlon Pinedo
    last modified by Marlon Pinedo
  • Error: Mooney-Rivlin constants  (A+B) < 0 from curve fitting

    Hello there,    I was trying to do a nonlinear simulation with Polyurethane material with Model Mooney Rivlin. I got the S-S curve data(uniaxial, biaxial and planar raw data)  from Matereality, but no ...
    Felix Yang
    last modified by Felix Yang
  • Jacobian exceeded the accepted limit for an element

    Hello!   Is anybody able to tell me what this message means in my study? I have found it that the max Jaobian number on mesh quality plot is 25ish which I think it is still acceptable (lower than 40). Even if I ...
    Michal Kolbuc
    last modified by Michal Kolbuc
  • Why is my simulation not considered converged?

    I don't understand how convergence criterion works. In the case pictured - the criterion is set manually to 0.5 m/s velocity and 0.5 kg/s mass flow. What are these numbers measured against? I would assume that they ar...
    Martin Malmqvist
    last modified by Martin Malmqvist
  • I try to run a simple static simulation. I usually have to re-mesh. Then sometimes it works, most times I get the message Unable to create plot do to requested quantity cannot be found in results file . Today, I did a force study on a pipe and it ran fine

    I try to run a simple static simulation. I usually have to re-mesh. Then sometimes it works, most times I get the message below. Today, I did a force study on a pipe and it ran fine, the I did an FOS study and got res...
    David Becker
    last modified by David Becker
  • How to find Static Pressure across System

    I have created a system that replicates the air flow capacity of the fan I am thinking about using. My problem is I don't know what the static pressure drop across the system is. Is there a way to find this out either...
    Michael Youngman
    created by Michael Youngman
  • Stopped running studies

    I ran simulation one or twice today, simple static. Now, I try a new identical study and it tells me:  the requested quantity cannot be found in the result file and the study doesn't run. I've deleted all my...
    David Becker
    last modified by David Becker
  • anyway to copy sw simulation features from one assembly to another?

    (contacts, bolts, etc from assembly file to another? Or to merge two assembly files with different studies and then copy over the features?
    Drew Plichta
    last modified by Drew Plichta
  • Pressure Drop across porous media.

    I have been reading through the Flow Simulation Technical Reference and found a series of equations to calculate the pressure drop. I have found two (2) equations that are quite useful (for anyone interested they are ...
    Michael Youngman
    last modified by Michael Youngman
  • What is the difference between Static Pressure, Environmental Pressure and Total Pressure when selecting a pressure opening as a boundary condition.

    I cat see to figure out the difference between these three selections, could some pleas explain. Thanks.
    Michael Youngman
    last modified by Michael Youngman
  • Help with Flow Simulation Wizard

    Can someone explain what changing the parameters on the last page of the wizard in flow simulation does? I have attached a picture of the page of which I am talking about.
    Michael Youngman
    last modified by Michael Youngman
  • Calculating lift over an airfoil

    I need to calculate the lift generated if that airfoil was moving through air at sea level  at a velocity of 100 m/s.  Resolve those distributed loads into evenly spaced loads over the edges of the airfoils....
    Stevie Mixon
    last modified by Stevie Mixon
  • Correct application of Force load in static simulation

    Hello all -   I've created a welded stand that I would like to perform a static simulation on.  I have created the stand using weldments, and fixed the bottom joints.  I then applied a force 10,000 lbs...
    Powell Barber
    last modified by Powell Barber
  • WHY DOES TERMINATING MESH TAKE EXCESSIVE TIME?

    terminating mesh takes a long time
    Michael Koss
    last modified by Michael Koss
  • Camera FOV Simulation Help

    I am using cameras in my assembly and want to simulate field of view(FOV) of those cameras such that parts in the assembly do not interfere with the FOV. I can move the cameras around if needed but was wondering if th...
    Chinmay Nanda
    last modified by Chinmay Nanda
  • Recommendation for constraint 

    Need recommendation for a fixture (constraint).  I have a tube with an applied load (torque) at one end and is sitting on a support at the near the opposite end.  Need some advise as to what type of fixture ...
    Greg Pedersen
    last modified by Greg Pedersen
  • CSWP-FEA (Simulation) sample exam, manual Calculation 1.

    Hi, colleagues! Am preparing for CSWP-simulation exam. Have some problems with sample exam. My first problem: Manual Calculation 1. The right answer is 7.354 lbs. But what is the process of calculation in details, ...
    Evghenii Nazarov
    last modified by Evghenii Nazarov
  • Stupid question about constraints on cylindrical faces

    Hy everyone,   I was simulating bearings' radial stiffness with SW when I found out this problem. With reference to the highlighted face below, is it possible to constraint the face radially only in case of rad...
    Federico Bassi
    last modified by Federico Bassi
  • Model builds without errors, until I open the motion study

    My model seems to have no errors or warnings after rebuild, but errors show up when I open the motion study tab.  Further, if I rebuild while the motion study is open, the errors appear in the model itself. ...
    Elizabeth Brownell
    last modified by Elizabeth Brownell